HGM125 Ring Roller Grinding Mill
Source:nclirik
Posted:2021-10-19
Today, we recommend a grinding mill that specializes in processing ultra-fine calcium carbonate: HGM125 ring roller grinding mill.
The grinding ring inner diameter of HGM125 ring roller grinding mill is 1.25m, the main grinding unit power is 185KW, the fan power is 132KW, the powder separator is 75KW, and other small motors total 402KW.
HGM125 ring roller grinding mill has four layers of grinding rings. The turntable is divided into upper and lower combined turntables. There are 7 grinding rollers for the upper two layers and 9 grinding rollers for the lower two layers. 32 grinding rollers in total.
The grinding roller, grinding ring, shaft pin and turntable are made of silico-manganese alloy steel. Bearing steel can be selected for special materials and high-hardness materials.
HGM125 ring roller mill produces 325 mesh calcium carbonate, which can produce 13-15 tons in an hour.
The hourly output of 1250 mesh can reach 4.5-6 tons, and it can produce 24 hours without stopping.
The fineness range of HGM125 ring roller mill can be adjusted from 150 mesh to 2000 mesh.
When the HGM125 grinding mill is equipped with a multi-head analyzer, the content of 2 microns can reach up to 65%.
HGM125 grinding mill is dedicated to the grinding of non-metallic minerals, such as limestone, calcite, marble, chalk, dolomite, carbon black, kaolin, bentonite, talc, mica, magnesite, illite, pyrophyllite, vermiculite, sepiolite, attapulgite, rectorite, diatomite, barite, gypsum, Alunite, graphite, fluorite, phosphate rock, potash ore, pumice and more than 100 kinds of materials.
Shanghai Clirik Machinery Co.,Ltd provide project site inspections, and one-on-one project managers are responsible for the entire project.
To ensure that the project is successfully put into production on time and with quality, welcome contact us freely.
The complete configuration of HGM125 series pulverizer includes hammer crusher, bucket elevator, storage bin, vibrating feeder, micro-grinding host, frequency conversion classifier, double cyclone dust collector, pulse dust removal system, high-pressure fan, Air compressor, electrical control system.
When working, the main motor drives the main shaft and the turntable to rotate through the reducer, and the roller pins on the edge of the turntable drive dozens of grinding rollers to roll in the grinding ring raceway.
The large pieces of material are crushed into small particles by the hammer crusher, and then sent to the storage bin by the elevator, and then sent to the bulk tray on the upper part of the turntable evenly through the vibrating feeder and the inclined feeding pipe.
The material is scattered to the periphery of the circle under the action of centrifugal force, and falls into the raceway of the grinding ring, and is impacted, rolled, and ground by the ring roller. After three-layer ring processing, it becomes powder. The high-pressure fan removes the external air through suction. Inhale into the machine, and bring the crushed material into the powder concentrator.
The rotating impeller in the powder classifier makes the coarse materials fall back and regrind. The fine powder that meets the requirements enters the cyclone powder collector with the airflow and is discharged by the discharge valve at the lower part of the cyclone as the finished product, while the airflow with a small amount of fine dust passes through After the pulse dust collector is purified, it is discharged through a fan and a muffler.
1. The average working diameter is increased to 1300mm, and the number of grinding rollers is increased to 44;
2. The output of finished products can reach up to 15 tons per hour.
3. The shape length * width * hight : 19261*4406*8591 mm, large volume and large capacity.
HGM series 125 mills have very low vibration, low noise, stable mechanical operation and reliable performance. Compared with traditional pulverizers, it has obvious advantages, greatly increasing the number of grinding rollers and reducing the spindle speed, thereby greatly increasing the output. HGM125 mills continue to use pulse processing equipment to reduce dust emissions, reduce noise, environmental protection and cleaner.
CLIRIK has a first-class manufacturing base with standardized and intelligent production lines.
CLIRIK's professional R&D, sales, installation and after-sales teams have provided door-to-door services to more than 100 countries and regions.
YGM Raymond mill: 613-33 micron(30-325 mesh); D90=30 micron
CLUM vertical roller mill: 20-5 micron(600-3000 mesh); D50=2 micron D97=4 micron
Email: [email protected]
WhatsApp: +8613512155195/+8613917147829
HGM125 Ring Roller Grinding Mill
The grinding ring inner diameter of HGM125 ring roller grinding mill is 1.25m, the main grinding unit power is 185KW, the fan power is 132KW, the powder separator is 75KW, and other small motors total 402KW.
HGM125 ring roller grinding mill has four layers of grinding rings. The turntable is divided into upper and lower combined turntables. There are 7 grinding rollers for the upper two layers and 9 grinding rollers for the lower two layers. 32 grinding rollers in total.
The grinding roller, grinding ring, shaft pin and turntable are made of silico-manganese alloy steel. Bearing steel can be selected for special materials and high-hardness materials.
HGM125 ring roller mill produces 325 mesh calcium carbonate, which can produce 13-15 tons in an hour.
The hourly output of 1250 mesh can reach 4.5-6 tons, and it can produce 24 hours without stopping.
The fineness range of HGM125 ring roller mill can be adjusted from 150 mesh to 2000 mesh.
When the HGM125 grinding mill is equipped with a multi-head analyzer, the content of 2 microns can reach up to 65%.
HGM125 grinding mill is dedicated to the grinding of non-metallic minerals, such as limestone, calcite, marble, chalk, dolomite, carbon black, kaolin, bentonite, talc, mica, magnesite, illite, pyrophyllite, vermiculite, sepiolite, attapulgite, rectorite, diatomite, barite, gypsum, Alunite, graphite, fluorite, phosphate rock, potash ore, pumice and more than 100 kinds of materials.
Shanghai Clirik Machinery Co.,Ltd provide project site inspections, and one-on-one project managers are responsible for the entire project.
To ensure that the project is successfully put into production on time and with quality, welcome contact us freely.
The equipment composition of HGM125 series grinding mill
The complete configuration of HGM125 series pulverizer includes hammer crusher, bucket elevator, storage bin, vibrating feeder, micro-grinding host, frequency conversion classifier, double cyclone dust collector, pulse dust removal system, high-pressure fan, Air compressor, electrical control system.
Working Principle of HGM125 Ring Roller Grinding Mill
When working, the main motor drives the main shaft and the turntable to rotate through the reducer, and the roller pins on the edge of the turntable drive dozens of grinding rollers to roll in the grinding ring raceway.
The large pieces of material are crushed into small particles by the hammer crusher, and then sent to the storage bin by the elevator, and then sent to the bulk tray on the upper part of the turntable evenly through the vibrating feeder and the inclined feeding pipe.
The material is scattered to the periphery of the circle under the action of centrifugal force, and falls into the raceway of the grinding ring, and is impacted, rolled, and ground by the ring roller. After three-layer ring processing, it becomes powder. The high-pressure fan removes the external air through suction. Inhale into the machine, and bring the crushed material into the powder concentrator.
The rotating impeller in the powder classifier makes the coarse materials fall back and regrind. The fine powder that meets the requirements enters the cyclone powder collector with the airflow and is discharged by the discharge valve at the lower part of the cyclone as the finished product, while the airflow with a small amount of fine dust passes through After the pulse dust collector is purified, it is discharged through a fan and a muffler.
The new features of Clirik HGM125 series grinding mills
1. The average working diameter is increased to 1300mm, and the number of grinding rollers is increased to 44;
2. The output of finished products can reach up to 15 tons per hour.
3. The shape length * width * hight : 19261*4406*8591 mm, large volume and large capacity.
HGM series 125 mills have very low vibration, low noise, stable mechanical operation and reliable performance. Compared with traditional pulverizers, it has obvious advantages, greatly increasing the number of grinding rollers and reducing the spindle speed, thereby greatly increasing the output. HGM125 mills continue to use pulse processing equipment to reduce dust emissions, reduce noise, environmental protection and cleaner.
The Parameter of HGM125 Ring Roller Grinding Mill
| Model | HGM80 | HGM80A | HGM90L | HGM100L-Ⅱ | HGM100P | HGM125L | HGM1680L |
| Ring Diameter(mm) | 800 | 800 | 900 | 1000 | 1000 | 1250 | 1680 |
| Ring Number (PCS) | 3 | 3 | 4 | 4 | 4 | 4 | 4 |
| Input Size (mm) | ≤10 | ≤10 | ≤10 | ≤15 | ≤15 | ≤20 | ≤20 |
| Output Size (mesh) | 150-3000 | 150-3000 | 150-3000 | 150-3000 | 150-3000 | 150-3000 | 150-3000 |
| Capacity (t/h) | 0.5-5.5 | 0.5-5.5 | 0.8-6.5 | 1.2-10 | 1.2-11 | 2.5-20 | 5-45 |
| Outlet Size L*W*H (mm) | 8605*4139*6050 | 10454*3393*6626 | 11735*3952*7525 | 14507*3633*7562 | 14362*4200*7562 | 19261*4406*8591 | 25067*5414*9007 |
| Main motor power (kw) | 75 | 75 | 55*2 | 132/75*2 | 132/75*2 | 185 | 315 |
Cases of HGM Ring Roller Grinding Mill
Who We Are?
Shanghai CLIRIK Machinery Co.,Ltd. has been committed to the field of ultra-fine powder grinding machines for 20 years.CLIRIK has a first-class manufacturing base with standardized and intelligent production lines.
CLIRIK's professional R&D, sales, installation and after-sales teams have provided door-to-door services to more than 100 countries and regions.
Which Models Can Be Selected For Processing Ultra-fine Powder?
HGM grinding mill: 74-5 micron(200-2500 mesh); D97=5 micronYGM Raymond mill: 613-33 micron(30-325 mesh); D90=30 micron
CLUM vertical roller mill: 20-5 micron(600-3000 mesh); D50=2 micron D97=4 micron
How to Get The Latest Quotation?
You can leave a message online or contact CLIRIK directly:Email: [email protected]
WhatsApp: +8613512155195/+8613917147829
Related Newsmore >>
- CLUM Series Mill: Eco-Friendly and Energy-Saving, Leading Ultra-Fine Powder Production to New Height2024-11-12
- Efficient Grinding Of Calcium Carbonate & Calcium Oxide: HGM125 Ultrafine Grinding Mill in Liaoning2024-11-01
- HGM Micro Powder Mill: Efficient Solution for Shell Powder Processing2024-10-24
- Gypsum Powder Manufacturing Process Using HGM Micro Powder Grinding Mill2024-09-28
- EXPOMINA PERÚ 2024-Set Off Again With a Full Harvest2024-09-18
- CLIRIK Ball Mill For Copper Ore Processing Plant2024-09-05
